Tools

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool

To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)

This dual-sided brush is specifically designed for cleaning hard-to-reach areas of the bicycle drivetrain. The long, stiff bristles of the GSC-3 are narrow enough to reach between the gears of tightly-spaced modern cassettes, while the slim contoured end is capable of picking grit and grime out of tight spaces such as derailleur pulley wheels.

Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.

Shorten your steerer, trim your handlebars and always make sure to measure twice with Park's Hack Saw. It features an outstandingly rigid aluminum die-cast frame with a blade tension adjuster and a superbly comfortable handle. The SAW-1 comes with one blade and accepts all 12-inch (300mm) replacement blades.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's AWS-8 Hex Wrench Set features Bondhus balldriver ends, which facilitate use when the tool is at an angle to the bolt. This is great for working in hard-to-reach areas, such as reaching water-bottle-cage screws. The AWS-8 has 4, 5, and 6mm wrenches, which are the most common bicycle bolt sizes. Plus, its Y shape and vinyl coating provide excellent leverage and comfort.

Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.

Precisely machined for a perfect fit, this 8-notch tool removes and installs the lockring that retains front chainrings found on Bosch Gen 2 e-bike motors after the crank arm is removed. - Fits Bosch Active Line (chainrings less than 20 teeth), Performance Line and Performance Line CX models - For lockrings with 50mm outside diameter and 8 notches - Replacement for Bosch 0275009003 tool - Torque wrench compatible 3/8-inch square drive - Constructed of 4140 heat treated steel and plated for long life

Designed and built to remove and install the lockring that retains front chainrings found on Shimano STEPS e-bike motors. - Fits Shimano STEPS E6100, E7000, E8000 and E9000 e-bike motor systems - For lockrings with 54mm outside diameter and 16 notches - Replacement for Shimano TL-FC39 tool - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - Constructed of 4140 heat-treated steel and plated for long life

Designed and built to remove and install Shimano direct mount chainring lockrings found on XTR 9120, XT 8120, MT900, and other Shimano direct mount systems. Precisely CNC machined from 6061 aluminum for a perfect fit and to prevent marring expensive parts. - Machined flat face for optimal lockring engagement - For lockrings with 41mm outside diameter and 16 notches - 36mm hex drive to be used with Park Tool TWB-36 Crow Foot and a torque wrench to properly measure torque - 6061 aluminum construction

Park's Oversize Adjustable Saw Guide guides a hacksaw so that you can accurately cut fork steerers, airfoil-shaped seatposts and more. The guide is made to be held in a vise and it has hardened-steel cutting slots and a secure clamp for the part you're cutting so that you make a perfect cut every time. The guide is compatible with round tubes from 1 to 1-3/4 inches in diameter and airfoil shaped parts up to 3.5 inches long. There are slots for standard and carbon-specific saw blades.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

Park's Pin Spanners are designed for maximum usefulness and versatility at the best value. Tough high-carbon tool steel is used to ensure long life and the handles are vinyl coated for a great grip and color-coded for easy identification. The green-handled SPA-1 is used to turn the adjustable bottom-bracket cup found on most 3-piece cranksets.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's Side Cutter Pliers are professional quality, 7-inches long, and made from heat-treated, forged chromoly steel for crisp, easy cuts and durability. They boast soft-touch, dual-density handles for an excellent grip, too.

The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.

Three of the most common Torx compatible wrench sizes in our classic 3-way design. The TWS-3 is useful for disc rotor bolts (T25), chainring bolts (T30), and hydraulic brake work (T10). TWS-3 FEATURES - T10, T25 and T30 Torx compatible set - Wrenches made from industrial tool steel, through hardened and tempered for long life

Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless forks. Slide on the guide, clamp it down and the hardened-steel cutting slot ensures a perfect cut every time. You can remove as little as 1mm, too.